Skip to content
  • Contacts
Electronics manufacturer for IoT
  • Home
  • Shop
  • Posts
  • Useful
    • GGreg20_V3 Ionizing Radiation Detector
    • Our modules: real demo
  • English
    • Українська (Ukrainian)
  • 00грн.
00грн.
  • Home
  • Shop
  • Posts
  • Useful
    • GGreg20_V3 Ionizing Radiation Detector
    • Our modules: real demo
  • English
    • Українська (Ukrainian)
  • 00грн.
  • Contacts

ESP8266 + door / window sensor (NodeMCU (LUA) – without Arduino)

  • Post published:17.10.2021
  • Post category:News/Tips

This guide shows you how to build a door / window sensor only with ESP8266 and NodeMCU (LUA) - without Arduino. The EasyIoT interface is used to display the status…

Continue ReadingESP8266 + door / window sensor (NodeMCU (LUA) – without Arduino)

Tags

Arduino Arduino UNO bus interface splitter DIY DIY (do it youself) dosimeters driver ESP-IDF ESP32 ESP8266 ESP Home ESPHome Expressive Geiger Geiger Geiger-Counter-Device Geiger-Muller tube GGreg20_V3 GPIO high voltage generator Home-Assistant Home Assistant I2C I2CHUB_V1 I2CUI4 I2CUI4_V1 Ionizing-Radiation ionizing radiation IoT devices ISR Li-Ion 16340 lora LUA MCP23017 MCU MicroPython NodeMCU Pulse Counter SBM20 STM32 Tasmota tindie UART Розроблено і виготовлено в Україні дозиметр

Our contacts

  • Mobile+38 (098) 892-57-94Opens in your application
  • Mobile:+38 (063) 486-70-47Opens in your application

New publications

  • Why we didn’t add the I2C interface to the GGreg20_V3 module
    Why we didn’t add the I2C interface to the GGreg20_V3 module
    28.05.2022/
    0 Comments
  • The GGreg20_V3 radioactive particle detector is installed in Budapest, Pest, Hungary and connected to the radmon.org service.
    The GGreg20_V3 radioactive particle detector is installed in Budapest, Pest, Hungary and connected to the radmon.org service.
    24.05.2022/
    0 Comments
  • The GGreg20_V3 radioactive particle detector is installed in Dornstadt, Baden-Württemberg, Germany and connected to the radmon.org service.
    The GGreg20_V3 radioactive particle detector is installed in Dornstadt, Baden-Württemberg, Germany and connected to the radmon.org service.
    07.05.2022/
    0 Comments

We are in social networks

  • FACEBOOKOpens in a new tab
  • TWITTEROpens in a new tab
  • Cart
Copyright - IoT-devices.com.ua
Select your currency
UAH Ukrainian hryvnia
USD United States (US) dollar
×
×

Cart

Yaml

може сховати лістинг у акордеон?
####### ggreg20_esp8266_esphome.yaml #####
esphome:
  name: esphome_node1 # Controller Unique Name
  platform: ESP8266 # Platform type you have to select when creating new yaml-config in ESP Home
  board: nodemcuv2 # Controller type you have to select when creating new yaml-config in ESP Home

wifi:
  ssid: "YourWiFiSSID"
  password: "SSIDPassword"

  # Enable fallback hotspot (captive portal) in case wifi connection fails
  ap:
    ssid: "Esphome Node1 Fallback Hotspot"
    password: "Cpxg9hRIBU7M"

captive_portal:

# Enable logging
logger:

# Enable Home Assistant API
api:
  password: "APIpassword"

ota:
  password: "OTApassword"

# Just embedded test D3 (GPIO0) button on every ESP8266 Devboard
# You can press D3 button several times to simulate incoming GGreg pulses
binary_sensor:
  - platform: gpio
    name: "D3 Input Button"
    pin:
      number: 0
      inverted: True
      mode: INPUT_PULLUP

# Here we calc and include to the firmware a power and doze values of ionizing radiation as sensor outputs
sensor:
- platform: pulse_counter
  pin: D3
  unit_of_measurement: 'mkSv/Hour'
  name: 'Ionizing Radiation Power'
  count_mode: 
    rising_edge: DISABLE
    falling_edge: INCREMENT
  update_interval: 60s
  accuracy_decimals: 3
  id: my_doze_meter
  filters:
    - sliding_window_moving_average: # 5-minutes moving average (MA5) here
        window_size: 5
        send_every: 5      
    - multiply: 0.0054 # SBM20 tube conversion factor of pulses into mkSv/Hour 
- platform: integration
  name: "Total Ionizing Radiation Doze"
  unit_of_measurement: "mkSv"
  sensor: my_doze_meter # link entity id to the pulse_counter values above
  icon: "mdi:radioactive"
  accuracy_decimals: 5
  time_unit: min # integrate values every next minute
  filters:
    - multiply: 0.00009 # obtained doze (from mkSv/hour into mkSv/minute) conversion factor: 0.0054 / 60 minutes = 0.00009; so pulses * 0.00009 = doze every next minute, mkSv.
####### END of ggreg20_esp8266_esphome.yaml #####

 

[contact-form-7 id=”298″ title=”Contact form”]