The I2C bus also allows hot connection\/disconnection of slave devices and identification of devices by addresses, or unique internal register data. The bus topology and at least 7-bit addressing allow up to a hundred slave devices to be connected to the I2C network simultaneously.<\/span><\/p>\n All this allows to build a convenient, reliable, and functional infrastructure of sensors and actuators around the main controller.<\/span><\/p>\n The main controller, however, usually has only one I2C interface and\/or a limited number of free pins. That is why, in order to fully use the I2C bus in the development and operation, interface splitters are used. And then through the splitter connect to the main controller the required number of sub-components.<\/span><\/p>\n The offered device is specially designed for such tasks – I2CHUB_V1 – splitter and converter of interface connector types in one module.<\/span><\/p>\n The I2CHUB module will be useful for:<\/span><\/p>\n On the module, as one of the delivery options of the User’s choice, it is possible to install six connectors (4 pins 2.54) with I2C interface and two connectors (2 pins 2.54) for the power supply. The User can also add the required number of appropriate interface cables to the kit when ordering.<\/span><\/p>\n The I2CHUB interface splitter module is a passive device and allows you to connect several (up to five) devices (sensors or actuators) to the main controller at the same time. The controller and splitter form a network of connected I2C devices with a bus-type topology and Master-Slave interaction profile. <\/span><\/p>\n Also, if you install different connectors (JST and\/or Dupont) on the board of the splitter module, I2CHUB will also act as a converter of physical interfaces, which is very convenient for prototyping and development.<\/span><\/p>\n Multiple I2CHUB devices can be freely cascaded within the limits allowed by the I2C bus specification, and further, expand the total number of free ports in the network of subordinate smart devices of the master controller.<\/span><\/p>\n The main controller which will work in the \u201cMaster mode\u201d is connected to one of the 4-pin ports of the module. Subordinate devices are connected to other 4-pin ports. In this scheme, all devices are powered by the main controller, and the 2-pin power connectors on the I2CHUB module board are not involved.<\/span><\/p>\n Power connectors can only be used if each of the devices on the bus is powered from its own source. <\/span><\/p>\n For example, the main controller can feed only itself and then only the interface signals are connected to the splitter: SDA, SCL, GND – without power, but with a common “ground” signal for all devices on the bus. <\/span><\/p>\n In this case, slave devices connected to the I2CHUB splitter must be powered directly from it:<\/span><\/p>\n <\/p>\n WARNING!<\/b> Be careful when designing – do not allow the current to run on the bus from multiple power sources – the devices on the bus will be damaged under the counter-current impact.<\/span><\/p><\/blockquote>\n <\/p>\n If you want to use an additional I2CHUB splitter, then instead of one of the slave devices you may connect an additional splitter, and then connect to it other devices that do not have enough free ports on the first splitter.<\/span><\/p>\n To build a personal weather station, it is necessary to connect a number of sensors to the controller to measure ionizing radiation, ultraviolet light, temperature, atmospheric pressure, relative humidity, and to detect lightning strikes.<\/span><\/p>\n The Bill of Materials, in this case, it is possible to make as the following:<\/span><\/p>\n <\/p>\n As we can see in this example, with a fairly wide functionality of the weather station, only one I2CHUB splitter will be enough to connect via I2C bus all the sensors listed to the main controller. <\/span><\/p>\n Moreover, if it is necessary to expand the weather station with new sensors (for example, add a light sensor: MAX44009, I2C), it will be easy to do just by using one more splitter. In this scenario, we get 4 more free I2C ports.<\/span><\/p>\n Note: <\/i><\/strong>The user can install his own 2.54 mm connectors on such a board<\/span><\/p><\/blockquote>\n The module board has the following linear dimensions: <\/span><\/p>\n\n
Description<\/b><\/h2>\n
Connection<\/b><\/h2>\n
\n
Recipe application as an example<\/b><\/h2>\n
\n
Product delivery kits.<\/b><\/h2>\n
\n
Basic Kit:<\/span><\/h3>\n<\/li>\n<\/ol>\n
\n
Technical description: i2chub_v1-product-description-and-datasheet-ukr<\/a>, i2chub_v1-product-description-and-datasheet-eng<\/a>.<\/h3>\n
Dimensions<\/b><\/h2>\n
![\"I2CHUB_V1](\"https:\/\/iot-devices.com.ua\/wp-content\/uploads\/2022\/01\/i2chub_v1-pcb-size-ports-scaled.jpg\")
<\/a><\/p>\n